Quick answer: Entrance mats ruck and curl after cleaning when they go back down damp, onto a wet floor, with a crease set in during drying, or with the wrong backing for the floor. To keep them flat and safe, dry each mat fully and flat (or hung, where the maker allows), make sure the floor underneath is clean and dry, lay it square with the pile facing up, then walk the edges and check that wheels roll across without catching. HSE's hazard-spotting checklist lists mats with curled-up edges as an entrance trip hazard and says to fix down the edges or replace the mat.
Rawlins has supplied cleaning equipment, chemicals and matting to UK businesses since 1981. This guide, for facilities managers, cleaning contractors and reception teams, picks up where most cleaning advice stops: the moment the clean mat goes back down.
Why entrance mats ruck and curl after cleaning
The usual causes are practical:
- Relaid damp. A mat that is still wet underneath can slide on a hard floor and traps moisture against the floor finish.
- Relaid on a wet or dirty floor. Grit and water under the backing stop it sitting flat and reduce grip.
- A crease set during drying. Folding, stacking or draping a wet mat over a narrow rail can leave a ridge that does not relax straight away.
- The wrong backing for the floor. A flat backing is intended for hard floors and a gripper backing for carpets. Swapping mats between doors can put the wrong one down.
- Laid off-square. A mat butted hard against a door frame or threshold strip can bow in the middle.
- Wear. A worn or damaged border may not lie flat however carefully it is laid.
HSE's slips and trips hazard-spotting checklist (CK4) asks whether there are trip hazards at entrances, including "mats with curled up edges", and suggests housekeeping: "fix down mat edges or replace if necessary". It also flags the floor between the threshold and the entrance matting as a slip risk when wet, which is why the floor matters as much as the mat.
Drying and storing mats properly
Drying is where most curling starts. Follow the mat maker's care guidance first. For WaterHog mats, the WaterHog care guide says to take the mat out of the machine as soon as the cycle finishes and lay it flat or hang it in a shady, breezy spot. It also says the mat and the floor should be completely dry before the mat goes back down.
Good drying habits
- Dry mats flat on a clean surface, or hang them evenly over a wide support, so the weight is spread rather than folded over a thin edge.
- Never stack wet mats face to face or leave them folded in a cleaning cupboard.
- Store dry spare mats flat, or rolled loosely with the pile facing out if space is tight, never folded.
Damp mats usually go back down because someone needs the door covered. Keep a clean, dry spare for each busy entrance so the cleaned mat can dry fully. Our machine guide for cleaning teams covers rotation and labelling mats as "in service", "drying" or "spare".
Re-laying checklist
Use this every time a mat goes back down. Keep a copy on the cleaning trolley or in the method statement.
| Step | Check | If not |
|---|---|---|
| 1. Mat dry | Backing and pile are dry to the touch, including the centre | Use the spare and leave this mat to dry |
| 2. Floor clean | Floor under the mat position has been swept or vacuumed, then mopped if needed | Clean it before the mat goes down |
| 3. Floor dry | No damp patches, especially near the threshold | Dry with a wet vac or allow time to dry |
| 4. Right backing | Flat back on hard floors, gripper back on carpet | Swap for the correct mat |
| 5. Pile up, square | Pile facing up, mat square to the door and not jammed against frames or strips | Lift and re-lay rather than dragging it |
| 6. Flatten | Walk the mat from the centre outwards to press out any ridge | If a crease remains, swap to a spare and let it relax flat |
| 7. Edges | All four edges and corners lie flat with no lift or wave | Re-lay, or withdraw and replace a damaged mat |
| 8. Wheel test | A trolley or cleaning cart rolls on and off without catching | Re-lay or withdraw the mat |
| 9. Record | Log the door, time and initials | — |
If a mat sits in a recessed mat well, clean and dry the well before re-laying. Our guide to cleaning recessed mat wells covers what builds up underneath and how to deal with it.
Accessibility checks
A mat that is fine underfoot can still stop a wheelchair, pushchair or trolley if a corner lifts or a ridge forms.
Approved Document M, volume 2 (buildings other than dwellings) says that where mat wells are provided, the surface of the mat should be level with the surface of the adjacent floor finish, and that internal floor surfaces next to the threshold should not impede the movement of wheelchairs. See the Approved Document M volume 2 PDF on GOV.UK.
Quick accessibility checks after re-laying
- Push a wheeled item (a cleaning trolley works) across the mat and over each edge. It should not snag or push the mat.
- In a mat well, check the mat sits level with the surrounding floor, not proud of it or sunk below it.
- Check the transition from the door threshold onto the mat is smooth.
- Make sure the mat has not crept into the swing of the door, where it can catch and lift.
Choosing mats that stay put
Construction makes a difference. The Tri Grip Heavy-Duty Mat has a 100% nitrile rubber backing that, according to the product page, resists cracking, curling, oils and many common cleaning chemicals. Its low-profile design is described as suitable for entrances used by wheelchairs, mobility scooters, pushchairs and trolleys, and it comes with a flat back for hard floors or a gripper back for carpets. Solid Colour Mats have a heavy-duty nitrile rubber backing that the product page says stays firmly in place on hard floors or carpets, a low-profile border, and the same choice of flat or gripper backing.
For WaterHog, our article on flat back or gripper back WaterHog mats explains which backing goes on which floor, and the full range is in our WaterHog collection.
When to stop re-laying and replace
Re-laying fixes a damp or creased mat, not a worn one. Withdraw a mat if an edge or corner still lifts after it is dry and correctly laid, if the border is split or crumbling, or if the backing no longer grips. CK4's advice is to fix down mat edges or replace the mat if necessary, so record the decision in your inspection log.
Frequently asked questions
Why do entrance mats curl at the edges?
Common causes are going back down damp, being dried folded or creased, being laid on a wet or gritty floor, using the wrong backing for the floor, and wear to the border. Dry the mat fully, clean and dry the floor, and re-lay it square. Replace it if the edge still lifts.
How long should an entrance mat dry before re-laying?
Until the backing and pile are completely dry, including the centre. Drying takes longer in cold, wet weather, so use a spare rather than relaying a damp mat.
Can I tape down a curling mat edge?
HSE's CK4 checklist suggests fixing down mat edges or replacing the mat if necessary. Check with the mat maker before taping, as some floor finishes and backings are not suited to tape. A mat that only stays flat when taped is often worn and due for replacement.
Should the pile face in or out when a mat is rolled for storage?
Store mats flat where you can. If space means rolling, roll loosely with the pile facing out and never fold the mat. Let it relax flat before it goes back into service.
Need help keeping your entrances safe?
We can help you choose entrance mats with the right backing for your floors and plan a cleaning and rotation routine. Browse our WaterHog mats and Tri Grip mats, call 0121 351 4444, email werner@rawlins.co.uk or use our contact page.